AH-1Z AH-64 C-17 CH-47 CH-53K E-2C F-15 F-16 F-22 KC-10 MISC UH-60 UH-72 V-22
F-15 MULTI-FUNCTION DISPLAYF-15 Multi-Function Display

The MFD10-121-001 is a simulated version of the 6 X 6 inch Multi-Function Display as used in the F-15 aircraft. It is intended for training and simulation purposes only.

The front appearance is a high fidelity duplicate of the original flight instrument, including the fully functional switch bezel and the AMLCD display. The AMLCD back-light and the bezel illumination meet NVIS requirements as specified in MIL-STD-3009.

The high resolution (768 by 768pixel) AMLCD is custom manufactured by resizing a commercial AMLCD panel from a 4 X 3 aspect ratio to a square format. The unit is ruggedly built to take the most demanding simulation environments. It is one of a wide family of cockpit simulation products and manufactured by Panel products Inc.

Video rate: 1024 by 768 pixels, (XGA) 48.3 KHz horizontal by 60 Hz vertical. The horizontal displayed image is a 768 pixel "cut out" section of the 1024 horizontal pixels available. It can be the right, left, or center portion, as selected by the internal video processor.

Video input connector: Standard 15 pin high density D type with separate R, G, B, H, and V inputs. The unit can accept all sync formats, separate H and V, Composite H and V, and Sync on Green.

Display technology: Resized commercial AMLCD with NVIS filtered white LED backlight Viewing angle is +- 80 degrees horizontal and vertical..

Environmental:OperatingStorage
1. Temperature10 to 35C-20 to 65C
2. Humidity20 to 90%0 to 95%
3. Shock/vibrationSuitable for ground benign and motion based trainers.

Power requirements: AC - 85-240 VAC, 47-63 Hz, power consumption 30 watts. Standard IEC 320 type receptacle. DC Voltage operation is available as an option, 20-32 VDC, (Unit is protected internally from accidental voltage reversal).

Bezel:
1. Twenty SPST momentary contact push buttons plus three SPDT momentary contact rocker switches. The switches are interconnected in a matrix format and direct connections to the matrix are available at the rear panel. Alternately, as an option, the bezel operation can be encoded into a serial data stream in RS232, RS422, or RS485 format.
2. Bezel backlight is NVIS compatible and is operated from 0 to 5 VDC or VAC at 3 amps maximum. Electrical connections to the backlight are available at the rear panel.

I/O connections, at rear panel of display:
1. J1 - Bezel interface connector, 26 pin high density "D", female sockets.
2. J2 - Video maintenance port, 9 pin "D", female sockets.
3. J3 - Video input connector, 15 pin high density "D", female sockets, standard VGA type connections.
4. J4 - AC power connection, standard IEC 320 input module with integral fuse and ON/OFF switch.

Other rear panel:
1. Power on LED, green.
2. Video presence and status LED, bi-color.
3. Cooling fan, draws air into unit from back, exits out both sides and top.

Physical:
1. Image area: 8.67 inch diagonal, 6.13 inch wide by 6.13 inch high.
2. Front bezel: 7.45 wide by 7.70 high by 2.95 thick.
3. Size behind bezel: 5.22 wide by 5.13 high by 7.38 deep.
4. Weight: 7.8 lbs.

Manufacturer of Simulation Displays &
Lighted Panels (310)830-3331 Contact
Contact
 About
About
 Home
Home
 Products
Products
 Services
Services